• Tachometer rebuild. Replaces old antiquated internals with complete state of the art components. Retains stock look but has modern tach accuracy and movement.........................................................................................................$180.00

  Recalibrate speedometer..............................................................................$20.00

  Rebuild and calibrate speedometer......................................Starting at $160.00

  Quarts clock conversions start at.............................................................$130.00

  Calibrate individual gauges:

  oil, temperature and fuel back to factory specs...................................each $15.00 

  Rebuild and calibrate individual gauges:

   oil, temperature and fuel.........................................................................each $55.00

   

  Rebuild altinator gauge................................................................................$65.00

   

Disassemble and clean cluster.

Polish lenses inside and out.

 Clean, remove rust, paint and reletter gauge face plates with decal kit.

 Recalibrate Oil, Temp and Fuel gauges.

 Paint indicator needles.

 Lubricate speedometer and trip odometer.

 Install an upgraded "Solid State" Instrument Voltage Regulator. Supply a reliable 5 volts of power to your gauges.  We up-grade your original voltage         limiter housing, you supply with cluster.

 

 

Install new reproduction woodgrain plates. These are beautifully reproduced plates, and are the closest you can get to factory original. Available in all configurations. (note: We no longer use woodgrain decals)

         

Must use original steel backing plate

Gauge side woodgrain plate installed (All years).................................$179.00

Switch side woodgrain plate installed (except convertable)...............$132.00

Switch side woodgrain plate installed (convertable)............................$155.00

Switch and knobs cleaned and indicators arrows or dots repainted..$5.00 ea.



 

 

 Reproduction Ebody rallye or standard dash headlight, rear defrost or top lift levers now available. Almost every switch lever we've seen has been cracked to some extent, even with pieces missing. These look and fit like the originals. Restore this important detail back to new again! $35.00ea.

                      

 

   Reproduction Ebody rallye dash indicator light tubes. These almost impossible to find parts that attach to the lens are now available with improved reinforced tab ears which make them stronger than the originals $22.50 ea. 

 

1968 -70 B-Body Rallye Dash

       

Available in white or black face.

Instrument Cluster Restoration $275.00

(Does not include bezel rechrome restoration)

 Disassemble and clean cluster with white repaint.

 Polish lenses inside and out, remove and repaint lens shield flat black.

 Clean, remove rust, paint and reletter gauge face plates with decal kit.

 Recalibrate Oil, Temp and Fuel gauges.

 Paint indicator needles.

 Lubricate speedometer and trip odometer.

 Install an upgraded "Solid State" Instrument Voltage Regulator. Supply a         reliable 5 volts of power to your gauges  We up-grade your original voltage         limiter housing, you supply with cluster.

 Install new BRAKE SYSTEM decal with new gasket.

 Install two new indicator gaskets.

 



 

1968 -70 B-Body Bezel Restoration



Includes chrome, black detail and white heat stamped lettering like the factory (not hand painted) $195.00

 

68-70 B-Body BRAKE SYSTEM Decal with Gasket $5.00 

(With Installation Instructions)

       

 

 

 

1968 -70 B-Body Rallye Dash Lenses

 Thin style only, Set $10.00

Switch Replating

Includes removal and installation from mechanism. Strip old chrome and replate.

  Rocker Style $25.00

Note: 1968-1969 flasher rocker buttons usually fall apart when the chrome shell is removed. This is due to years of expansion and contraction of the switch shaft pressed inside the plastic button. Some wiper rockers were manufactured from pot metal and are unrestorable to acceptable standards. We offer reproduction plastic replacement pieces.  If your button is damaged or pot metal we have new reproduction replacements available $35.00 each 

  Thumb Wheel  $27.50

Push Button  $15.95

Note: Push buttons usually fall apart when the chrome shell is removed. This is due to years of expansion and contraction of the switch shaft and metal retainer pressed inside the plastic button.  If your button is damaged we have new reproduction replacements available $32.00 each

We can replace your broken vacuum headlight door rocker arm. This extra arm controls the vacuum switch lever and your headlight doors will not operate without it.

•  

  

  Back to top